1-877-443-6276

PG9926 - DSC Wireless PowerG Smoke Detector

PG9926 - DSC Wireless PowerG Smoke Detector
PG9926 - DSC Wireless PowerG Smoke Detector
Item# PG9926

Please Note: The DSC PG9926 wireless PowerG smoke detector has been discontinued and replaced by the PG9936 model number.

DSC PG9926 Product Description:


The DSC PG9926 is a wireless PowerG smoke detector that provides early warning of developing fire by sounding an alarm with its built-in siren, and by transmitting an alarm signal to the security system. The PG9926 sensor provides alerts for smoke, tamper and device low battery conditions.

It is easy to install the detector on the ceiling with only a few holes needed to drill. Being wireless, the smoke detector offers home and business owners more choice as to where they are to be installed to include locations in which wiring is difficult or impossible. Maintenance is also easy, with audio and visual sensitivity degradation indicators notifying when detector cleaning/replacement is required.

Product Features:

  • Photoelectric smoke detector
  • Ensures reliable performance using built-in PowerG leading-edge wireless intrusion technology with two-way communication
  • Provides alerts for smoke, tamper and device low battery
  • Visible link quality indication shown on the device
  • Fully supervised
  • Maintenance and battery condition indication
  • Built in 85db Alarm Buzzer
  • Low battery indication
  • Prolonged battery life (8 years with typical use)
  • Backed by DSC's 1-year limited manufacturer's warranty

DSC PG9926 Product Specifications:


  • Dimensions: 4.7" x 2.3" in (120mm x 58mm)
  • Weight (including battery): 165g (5.8 oz)
  • Communication Protocol: PowerG
  • Battery Life: 5 years (for typical use)
  • Battery Type: 3V Lithium CR123A Battery (Panasonic or GP)
  • Tamper Alert: Tamper event (removal of the unit from its bracket) is reported once. Tamper restore is reported when the tamper switch is restored
  • Detector Type: Photoelectric
  • Alarm Sount Level: 85 dB at 3 m (10 feet)
  • Frequency Band: CE Listed PG4926: 433 MHz; PG8926: 868 MHz; FCC/IC/UL/ULC listed PG9926: 915 MHz
  • Alarm Report: In the alarm condition, the detector sends the alarm event to the control panel. When the alarm condition is restored, the detector sends an alarm restore event to the control panel and sets the alarm restore indication (red LED blinks once per sec.)
    Note: The alarm restore indication can be cleared via the control panel only.
  • Operation Voltage: From 2.5V to 3V
  • Current Drain: 22µA standby, 200 mA max. in operation
  • Smoke Density: Europe: 0.09 - 0.14 dB/m
  • Cover Range: 5 to 100 cubic meters (1770 to 3530 cubic ft.)
  • Battery Supervision: Automatic transmission of battery status data as part of any transmitted message
  • Low Battery Threshold: 2.5 V
  • Audible and Visual Low Battery Warning: Built-in horn beeps every 30 seconds simultaneously with red LED flashing (for up to 30 days when the battery voltage drops).
  • Audible and Visual Degraded Chamber Sensitivity Warning: Built-in horn beeps every 30 seconds in the middle of red LED flashing intervals - indicates that the detector must be replaced.
  • Clearn Warning Transmission: A clean (maintenance) signal is transmitted when the detector's chamber becomes stained, causing the detector to operate at high sensitivity.
  • Operating Temperature: 14°F to 131°F (-10°C to 55°C)
  • Storage Temperature: 4°F to 140°F (-20°C to 60°C)
  • Relative Humidity: up to 93% max. non condensing (UL/ULC verified max 85%)
  • Compatible Receivers: 433 MHz Band: HSM2HOST4; HS2LC-DRF(P)4; HS2ICN9RF(P)4; PG4920
    868 MHz Band: HSM2HOST8; HS2LCDRF(P)8; HS2IC-NRF(P)8, PG8920
    912-919 MHz Band: HS2HOST9; HS2LCDRF(P)9; HS2IC-NRF(P); PG9920
  • Approvals: FCC/IC, UL/ULC, CSFM

DSC PG9926 LED Indicators:


Placement Test:

  • Green LED blinks: Strong
  • Orange LED blinks: Good
  • Red LED blinks: Poor
  • No blinks: No communication


Audible and Visual Indications:

  • Smoke Alarm: Red LED light (flash every 500ms), 3 long beeps every 4 seconds
  • Tamper Alarm: Long beep every 2 seconds
  • Standby: Red LED Light (flash every 30 seconds)
  • Low Battery: Red LED Light (flash every 30 seconds), Short beep every 30 seconds
  • Smoke sensor trouble: Red LED Light (flash every 60 seconds) and Yellow LED Light (3 Flashes every 60 seconds), Short beep every 30 seconds
  • Low sensitivity alarm: Red LED Light (flash every 30 seconds), Short beep every 30 seconds
  • Need to clean: Red LED Light (2 flashes every 30 seconds), 2 Short beeps every 30 seconds

DSC PG9926 Product Compatibility:


  • DSC Iotega Control Panels
  • DSC PowerSeries Neo Control Panels
  • DSC PowerSeries Pro Control Panels
  • Qolsys IQ Panel 2 Plus Control Panels
Q & A's :

comments powered by Disqus
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