Product Features:

• ETL certified for UL639 and ULC S306
• 35-foot detection range with a 90-degree horizontal FOV
• Remotely configurable PIR sensitivity (Pet immunity, etc.)
• Easy Installation; Simple panel enrollment, No broadband required (No router configuration), Tri-color LED
• Battery powered
• Tamper detection, walk test mode, supervision
• Color images
• Night vision; IR illumination, Black and white images
• Wireless image transmission to panel
• Wireless image transmission to Alarm.com via cellular networks

Physical Data

• Dimensions (L x W x H): 3.0", 1.8", 1.8"
• Enclosure Material: Fire resistant plastic (UL 94)
• Enclosure Color: White
• Weight: 3.1 oz (with batteries, w/o mounting accessories)
• Operating Temperature: Indoors (32-110°F for non pet applications; 60-110°F for pet applications)
• Humidity: UL certified in up to 85% relative humidity
• Static Immunity: Yes
• Sealed Optics: No
• RFI Immunity: Yes
• Tamper Detection: Yes (orientation based detection)

Motion Detection

• Technology: Dual element PIR
• Detection Range: 35' with a 90° horizontal FOV
• Lens Type: Fresnel lens
• PIR Sensitivity: Remotely configurable; 3 levels
• Pet Immunity: Yes with low sensitivity level only (up to 40 lbs.)
• PIR White Light Immunity: Yes
• Walk Test Mode: Yes
• Post Activation Idle Time: 3 minutes (default when disarmed)

Camera

• Camera Type: CMOS
• Focus: 1 ft. to infinity
• Night Vision and Capture: Yes- automatic infrared flash (invisible 240mW)
• Night Vision Range: Optimal within 20 feet
• Minimum Illumination w/o IR Flash: 3 lux
• Motion Triggered Images: Yes
• Images On-Demand: Yes
• Image Resolution: VGA (640x480 pixels)

Wireless

• Frequency: 900 MHz
• Protocol: 802.15.4
• Open Air Range: 400 feet
• Antenna: Helical chip antenna
• Wireless Supervision: Yes
• Encryption: Yes

Electrical Data

• Operating Voltage: 2.3-3.5v
• Current Consumption (typical) <1mA
• Power Requirements: 2-AA 1.5v Lithium batteries
• Recommended Battery: Energizer Ultimate Lithium (included)
• Battery Life (typical): Approximately 3 years

Regulatory Compliance

• FCC: FCC ID: YL6-143IS300
• IC: IC: 9111A-143IS300
• RoHS: Compliant
• ETL: Certified for UL 639 compliance

• Mounting Height: 6 ft to 8 ft
• Mounting Angle: 6°, 12°, or 18° down angle
• Mounting Options: Wall mounted w/ bracket (flat or corner mount)

Interlogix Simon XT

• Panel version 1.3 & up
• Alarm.com module with firmware version 146 & up
• Image Sensor daughterboard for modules 185 or lower
• Device limit 3 image sensors

Interlogix Simon XTi

• Panel version 1.0 & up
• Alarm.com module with firmware version 151 & up
• Image Sensor daughterboard for modules 185 or lower
• Device limit 3 image sensors

Interlogix Concord

• Panel version 4.0 & up
• Alarm.com module with firmware version 177 & up for CDMA and 177 & up for HSPA 183 & up
• Image Sensor daughterboard version 104.0 & up or built-in radio with module versions 187+. Note: Image Sensor is not supported in the initial release of the Interlogix Concord module version 187. Future functionality will be brought via an Over-The-Air (OTA) firmware update
• Device limit 3 image sensors (must all be on the same partition)

DSC Impassa

• Panel version 1.3 & up
• Alarm.com module with SKU 3G8055(I) or CD8055(I)
• Image Sensor daughterboard for modules 185 or lower
• Device limit 3 image sensors

DSC PowerSeries Neo

• Panel version v1.10 & up
• Alarm.com module with SKU 3G8080(I), SKU TL880LT, or CD8080(I)
• Image Sensor daughterboard for modules 185 or lower
• Device limit 3 image sensors

DSC Touch

• All panel versions
• No daughterboard needed
• Device limit 5 image sensors

Qolsys IQ Panel

• All panel versions
• No daughterboard needed
• Device limit 5 image sensors

Qolsys IQ Panel 2

• All panel versions
• Requires daughterboard
• Device limit 5 image sensors

2GIG GC3

• Panel version 3.0.1 & up
• 2GIG XCVR3 Image Sensor Dongle
• Device limit 10 image sensors