46201 - GE Enbrighten Z-Wave Plus QuickFit In-Wall Smart Switch (by Jasco Products)
Please Note: The GE 46201 Enbrighten Z-Wave Plus QuickFit in-wall smart switch has been discontinued.
GE Enbrighten 46201 Product Description:
The GE Enbrighten 46201 is a Z-Wave Plus in-wall smart switch manufactured by Jasco Products (with white/light almond paddles included). The 46201 smart switch allows the end user to turn the connected device On/Off manually or via Z-Wave hub or controller.
Property automation is even smarter when paired with a compatible hub, the hardwired smart switch operates wall, ceiling and accent lighting through individual commands and programmed settings. Wirelessly control and schedule indoor or outdoor fixtures for effortless management of your home or business.
The GE Enbrighten 46201 has a QuickFit™ design that includes improved components which reduce the housing depth by up to 20 percent compared to previous Z-Wave models and eliminated the need for heat tabs. With SimpleWire™ auto line-load sensing terminals, the GE Enbrighten 46201 supports fast installation by detecting line and load wires and configuring the switch accordingly. Dual ground ports, which are offset to avoid switch box mounting screws, support daisy-chaining in multi-switch setups.
This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class.
Product Features:
- Turn the connected device On/Off manually or via Z-Wave hub or controller
- Remotely monitor with any mobile device
- Works with Google and Alexa (requires compatible hub*)
- May be used in single pole installation or with up to four GE model 12723 or 46199 Add-on switches in 3, 4, 5 or 6-way wiring configurations
- Works with most LED, CFL, halogen and incandescent bulbs
- Blue LED indicates switch location in a dark room (with 4 adjustable settings)
- Can be Included in multiple Groups and Scenes
- Utilizes the Z-Wave Firmware Update Meta Data command class for standardized firmware updates Over the Air
- Supports Advanced Configuration; LED status, Alternate exclusion
- Screw Terminal installation; requires wiring connections for Line (Hot), Load, Neutral, and Ground. Traveler wire required for multi pole installation
- Uses a standard decora wall plate (wall plate not included)
- Interchangeable Paddle switch: White & light almond paddle included in package
- LED status can be inverted manually changed to invert, always OFF and always ON
- Inline traveler circuit protection
- White/light almond paddles included
- Z-Wave Plus certified
- Compatible with Z-Wave enabled controller
GE Enbrighten 46201 Product Specifications:
- Power: 120VAC, 60Hz, 9W
- Maximum Load: 960W Incandescent, 1/2 HP Motor 1800W (15A Resistive)
- Signal Frequency: 908.4/916 MHz
- Z-Wave Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
- Operating Temperature: 32°F - 104°F (0°C - 40°C)
- Environment: Indoor Use
- Warranty: 2-year limited product warranty
Please Note: The GE Enbrighten 46201 smart switch requires a neutral wire.
GE Enbrighten 46201 Product Documents:
• Data Sheet - GE Enbrighten 46201 Z-Wave Plus In-Wall Smart Switch
• User/Installation Guide - GE Enbrighten 46201 Z-Wave Plus In-Wall Smart Switch
• How to Enroll, Delete and Reset - GE Enbrighten 46201 Z-Wave Plus In-Wall Smart Switch
GE Enbrighten 46201 Product Configuration:
- Adding your device to a Z-Wave network - Once the hub is ready to add your smart switch, press and release the top or bottom button on the smart switch to add it in the network.
- To remove and reset the device - Once the controller is ready to remove your device, press and release the top or bottom button on the smart switch to remove it from the network.
- S2 + SmartStart install - The controller's app will indicate if it has discovered the device. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box, or the QR code label on the product. Enter the 5-digit code.
- To return to factory defaults - Quickly press the ON button 3 times, then press the OFF button 3 times. The LED will flash ON/OFF 5 times when completed successfully.
